[GUIDE] error 12/43 & other detection, bootup, stability & performance issues
 
Notifications
Clear all

[GUIDE] error 12/43 & other detection, bootup, stability & performance issues  

 of  16
  RSS

Moussa Bayou
(@moussa_bayou)
Eminent Member
Joined: 1 year ago
 

Hello everyone,

I have a DIY eGPU (GTX 1050 + riser 006c + DIY EC adapter) setup, the problem is that it's not being detected on my HP Pavilion DV7-3160es notebook.

I tried turning the PSU on after halting windows from starting (pressing F8 before it starts), and the same except turning it on after the 4 dots emerged (w/o pressing F8). Even turning it on then turning my laptop on with no avail...

Specs:
HP Pavilion DV7-3160es
i5-430m with a weak iGPU
Geforce G105M dGPU
6GB of DDR3-1016mhz RAM

Any help? I can provide way more infos if necessary.

This post was modified 5 months ago

HP Pavilion DV7-3160es i5-430m 6GB RAM G105M dGPU.
Planned GTX1050 for an eGPU.


ReplyQuote
(@dudu18xb)
New Member
Joined: 1 year ago
 
Hello
I have a Lenovo IdeaPad S400U laptop

The settings are currently
Processor: Intel Core I5-3317U
RAM Memory: 8GB
SSD: 240 + 32GB

I recently bought a GTX 750 TI (Gigabyte GV-N75TD5-2GI) And a Geekworm Egpu 8.5 model

I installed everything correctly and I get an error 43.

I purchased Nando DIY eGPU 1.35 software, and followed the footsteps of this video:   https://www.youtube.com/watch?v=FTnnfaPCqxw  

I also researched other forums and videos and so far couldn't solve the problem. Can anyone help me with this problem?

I also checked this error using this Link I was not successful either :(
Sorry my English, I'm Brazilian and I'm writing here with the help of Google Translate to communicate with you.

Pending: Add my system information and expected eGPU configuration to my signature to give context to my posts


ReplyQuote
(@scoopspoof)
New Member
Joined: 1 year ago
 

Core i7 M620
Nvidia Quadro fx 880M

Using 220V ATX PSU +  PCE164P-N03  + 2 Port USB 3.0 Express Card ExpressCard 34mm + USB 3.0 A male to A male Cable
GPU -  Nvidia GT730 2GB

Problem 1 - Upon inserting Expresscard into the slot. The laptop simply doesn't boot up. It gets stuck on splash screen with no way to jump into bios.
Problem 2 - If expresscard inserted after booting up simply doesn't lets my GPU being detected in windows for obvious reasons

What I have done so far :
Changed Bios settings : 
Disabled PCI power management
Disabled PCI express power management.

So far its a disappointing failure with no solution to be found. 
Any help would be greatly appreciated

Pending: Add my system information and expected eGPU configuration to my signature to give context to my posts


ReplyQuote
(@pedro_augusto_rc)
New Member
Joined: 4 months ago
 

Greetings!I have a dell ispiron 3442 and i'm trying to put a GTX1660 on to it... Here's the thing, i made all the cables right and all but the pc when i turn it on with the graphics card it makes 6 loud beebs and does not recognise the egpu. Help please:'(

Pending: Add my system information and expected eGPU configuration to my signature to give context to my posts


ReplyQuote
(@shraey_chikker)
New Member
Joined: 4 months ago
 

Hi

I have an  exp gdc beast mcpie with 1060 3gb. Also, my laptop is lenovo z580 with i5 + gt 630m + 4gb ram. By default, my laptop doesnt boot with the  exp gdc  . So i halt boot WITHOUT wifi card, then boot re plug the egpu and boot. Still i'm not able to get it to show up in device manager. What could be the issue? does lenovo disable the mcpie slot if it detects nothing is plugged into it at boot? 

I haven't found any solution as of now. Is it because of the 630m that i haven't disabled? Also, there is no option to disable wake on lan / pxe on lan in my bios?

Any help is appreciated.

Thanks!

Pending: Add my system information and expected eGPU configuration to my signature to give context to my posts


ReplyQuote
Mlgfox
(@mlgfox)
New Member
Joined: 4 months ago
 

Greetings, I have a Inspiron 3442 and i buyed a brand new GTX 1660 and with that the damn 7 dollar mPCI ( R$124.00)- I made all the cables right n stuff but when i turn on the Notebook it makes 6 BEEPS and turn off the Egpu... i was about to give up ( after three days of failures ) i saw a user here, he managed out to make it work. two years ago but, you know. I run out of money and i'll make everyting thats possible to make it work. Help please.                                                                                                                              ?width=169&height=301 ?width=169&height=301

Inspiron 3442 -i5-4210u - 8GB ram- PCE164P-N03 > GTX 1660;(NOT WORKING, i need help)


ReplyQuote
(@gustavozoppi)
New Member
Joined: 4 months ago
 

Yesterday I purchased a RX 590 Nitro+ and a Corsair CX 450M

I have the GDC Beast 8.4d EXP adapter and when turning on the notebook with the external power supply turned on (for gpu to start with the laptop) the screen of both the notebook and my external monitor only black screen.

I already changed in the eGPU adapter so the card start with the boot delay, did not work. There is also an option mentioning "ATX" in the eGPU adapter, I also changed it to ON, and also got no video.

I am seeing if I suddenly find an "unlocked" bios for my notebook. My laptop bios is "AMIBIOS Version 17HX.M045.20121127.SSH"

I really apologize if a topic with the same subject has already been created and properly answered, but I have been looking for information and to no avail so far. If anyone can help, it would be greatly appreciated.

Pending: Add my system information and expected eGPU configuration to my signature to give context to my posts


ReplyQuote
(@ahmed_mohamed_el_zain)
New Member
Joined: 4 months ago
 
I did all steps on my laptop Hp probook 450g i5
it's work but I have low fps on pubg steam 30-40 on low setting with card asus astrix 1070 oc 
I saw its very low I need at least 90 fps
my Gpuz pic
This post was modified 4 months ago

Pending: Add my system information and expected eGPU configuration to my signature to give context to my posts


ReplyQuote
(@antoine_bon)
New Member
Joined: 4 months ago
 

Hi hi,

I'm new to eGPU's science and I got a problem.

 

When I plug in exp gdc 8.5c I got a black screen (both on internal and external display)

Here are my specs :

-HP probook 6460b (Single stick 8gb ram, i5 2520m)

-exp gdc beast 8.5c powered  ATX power supply (Corsair CX500) connected by mPcie

What I've tried :

Different GPU : Nvidia 9800GT, GTX 760 and a low profile AMD cardsame thing.

-Plug in HDMI cable to the eGPU adapter after paused windows bootup with f8/f12 : Nothing into device manager

-Plug in HDMI cable to the eGPU adapter after hibernating windows : Black screen, no boot up

-Set Power to ATX and set delay to 7s : Same thing, black screen

 

Does anyone have an idea ?

Pending: Add my system information and expected eGPU configuration to my signature to give context to my posts


ReplyQuote
(@koray_zagli)
New Member
Joined: 4 months ago
 

Good evening, I have a Lenovo ThinkPad x230. Intel i5-3230M. Latest BIOS update 2.77. With exp gdc 8.5v in express card and an Asus gtx 1050ti cerbersus. My graphics card is not recognized at all. How can I do? The fans are idling

Pending: Add my system information and expected eGPU configuration to my signature to give context to my posts


ReplyQuote
Mlgfox
(@mlgfox)
New Member
Joined: 4 months ago
 

Greetings, i'm trying to make a "Egpu" on a Dell Inspiron 3442-I5-4210U and i'm using a Egpu Beast 8.5 Mpci express with GTX 1660 6BG( Not TI ) Every time i boot the laptop it makes loud 6 BEEPS and turn of the Graphics card. i believe that it is whitelist,and if it is i have no idea how to make it , can you guys help me out?

Inspiron 3442 -i5-4210u - 8GB ram- PCE164P-N03 > GTX 1660;(NOT WORKING, i need help)


ReplyQuote
(@kjan1996)
Active Member
Joined: 2 years ago
 

hello everyone, i have the next problem: when i connect the PCE164p to mini pcie on the WLAN spot the notebook get black screen 

cold boot, and hot plug dont work.

already try  mod the mini pcie, to expresscard with an - USB 3.0 expresscard adapter but isnt recognized for windows, and 1.35 nando software

tape in pin 2 and pin 22 dont work 

 

i have the bios mod unlocked by DUDU of web "bios-mods"

notebook - lenovo T430 i7 3610qm

2x4gb 1600mhz

GTX 1650 zotac OC mini

riser PCE164-N03, 

PSU 12v 8amp for CCTV cams

somebody already try it? can helpme pls

and thanks

Pending: Add my system information and expected eGPU configuration to my signature to give context to my posts


ReplyQuote
(@aurel_k)
New Member
Joined: 4 months ago
 
Hi friends.
I really need help for my egpu.

I have a HP envy 15 with intel hd 4600, i7 4710hq core with 16 GB RAM.
I found an AMD RX 570 8GB graphics card to do my egpu.

I did my assembly and everything seemed to be fine. Even in the device manager the graphics card was recognized. When I connect my HDTV with hdmi it works well so I'm happy: love:: love:: love:
So my problem is that whenever I launch any application and the fans start to turn the screen disconnects with no signal. :cry: 
I do not know what is the problem and I hope to find a solution on forums but nothing. Please, I really need help. thank you.
 

Pending: Add my system information and expected eGPU configuration to my signature to give context to my posts


ReplyQuote
Papagoja
(@papagoja)
New Member
Joined: 5 months ago
 

Hello everyone, having some issues and I just wanna check so I haven't missed anything before I RMA the board. 

Everything works with PCIe set to Gen1, but as soon as I change the BIOS to PCIe Automatic the computer will boot, the card will be identified but the Nvidia control panel won't load and the GPU will not send any picture over HDMI/DP. 

Using an Dell DA-2 and the EXP GDC 8.5c with PTD set to 7 and ATX on default (ON?). Tried to add some ferrite rings to the 6 pins & aluminium foil around the EC cable. 
Is it a bad board or have I missed anything? 

 

Cheers.

 

Edit: Gen1 is working fine over, but the Nvidia control panel will not load with Gen2 speeds. No error message shown in device manager, just that the card will not transmit picture via HDMI/DP to the external screen and no way to access Nvidia control panel. 

I have shielded the HDMI-EC cable with Aluminium & Electric tape, Ferrite rings on 6pin-6pin & PSU-wall socket cable, all other cables have ferrite rings from factory. 

Tips? Is it possible to open up the Expresscard without breaking it and solder it on to another, shielded HDMI cable? 

This post was modified 4 months ago

Lenovo Thinkpad X230 Tablet with EXP GDC 8.5c & Dell DA-2 coupled with GTX 1060 6GB over Expresscard.


ReplyQuote
(@guilherme_vilhena)
Active Member
Joined: 4 months ago
 

@aurel_k

I have just built my build as well and I am facing a somehow a related issue:

System specs

  • MSI GE62 6QD 15.6-inch
  • CPU: Intel Core i7-6700HQ
  • iGPU: Intel 530
  • dGPU: GTX 960M
  • OS: Windows 10

eGPU hardware 

I have installed the eGPU to my machine and installed the most recent drives, but I am facing a funny problem:

When the eGPU is under load (game or benchmark) and with the HDMI cable connect directly from it to the monitor it starts to freeze. On games, for example, the screen starts to blink and of a sudden go black (it blink sometimes with the game image, and black for long periods again, and stay black). I have realized that when changed graphics setting from Highest to Lowest this problem is not so often. By the way, the game I was testing was Shadow of the Tomb Raider.

Another funny fact is that when I disconnect the HDMI from the eGPU and start to run the game on the built-in display, this problem does exist. If I connect the HDMI to the motherboard HDMI output, the problem returns.

I have disabled the  NVIDIA driver , but it does not solve it. I also disable the Intel 530 graphics, but no success at all.

The problem is not the HDMI cable, since I have used it until now, and it works perfectly. I can see in GPU-z that the port is working as it should (PCIe 16x 3.0)

Pending: Add my system information and expected eGPU configuration to my signature to give context to my posts


ReplyQuote
kenshin07
(@kenshin07)
New Member
Joined: 4 months ago
 

Brix Pro running windows 10. I have installed the egpu using the exp gdp v8.5 (that's what is written on the board) and I also tried another exp gdp board with both the GTX 1080 and 950 but all I get is a black screen. If I have an HDMI cable running from from the brix and one from the gtx, it will always show the integrated graphics. There is no way to turn off IG in the BIOS. I tried hot swapping the wifi card with the gdp exp but nothing is detected in the device manager. I have the card drawing PSU power constantly (by flipping the switch). I tried the various settings on the second switch (which I think is for delayed boot) but that doesn't work either. I had a similar brix pro using a gtx 1070sc and that worked fine. When I upgraded the PC and graphics card, I couldnt get them to work. It is unlikely that both gdp exp and both graphic cards are malfunctioning. Would I benefit from buying the diy egpu setup 1.35? Anything else I can do before purchasing it?

Pending: Add my system information and expected eGPU configuration to my signature to give context to my posts


ReplyQuote
(@boris_levit)
New Member
Joined: 1 year ago
 

Hey.

I'm running a Lenovo W530 I7 w16Gb ram, a Beast PCIe eGPU with an Nvidia 970 card.

I've played Witcher 3 pretty successfully on this configuration.

When I'm trying to play Skyrim SE (via Steam) on low detail quality the computer crashes to BSOD, it does so after I press "new game" on the initial splash screen.

The BSOD error is nvlddmkm.sys VIDEO-TDR-FAILURE

Any ideas?

Pending: Add my system information and expected eGPU configuration to my signature to give context to my posts


ReplyQuote
(@fluffy_ironboots)
New Member
Joined: 4 months ago
 

Hi,

I'm new to the Forum and trying to get my egpu to work.

My Laptop is an Samsung RF711

i7 2640m

Nvidia gt540m

I bought nando's Setup 1.35 to get it working.

First i tried my R9 290 but had no chance in getting it to recognize, hot swapping, putting Windows to sleep swapping and booting again, etc.

Nothing worked. Then i tried my rx590. On a cold boot i just get a black screen. If i time the Power of the PSU just right it gets recognized but when i'm trying to Install the driver i get a blue screen(Error was something with Video scheduler). I also tried to isolate the Pins like mentioned in nando's Guide, that also Changes nothing. So then i tried to make an uefi Install. When i get the GPU to recognize with an uefi Install i get an instant blue screen(page fault in nonpaged area).

I'm completely out of ideas how to get it working.

Samsung RF711
Intel i7-2630qm
AMD RX 590

EXP GDC Beast V8.5c mPCIE


ReplyQuote
(@akmal_jihad_almascaty)
Active Member
Joined: 4 months ago
 

Hey guys,

i just installed a testbuild to my lenovo G410 (i7 4700MQ)

My setup:

R9 270

500W PSU 

EXP GDC Beast V8.0 mPcie

The problem is, when i turned on the power supply, gpu and psu fan start spinning and stop immediately. What the problem with my setup? is my psu or exp gdc broken?

Thanks, sorry for my bad english

Pending: Add my system information and expected eGPU configuration to my signature to give context to my posts


ReplyQuote
arthurious
(@arthurious)
New Member
Joined: 4 months ago
 

Cheers people, I'm new to this, so please go easy on me :mrgreen: 

 

So I decided to build an egpu setup for my laptop and kinda got stuck at the very beginning...

My setup:

  • Voyo Vbook 3 pro (yoga-style chinese laptop) based on Apollo Lake SoC, Celeron n3450 cpu (4/4), intel HD 500 igpu, 8gigs of RAM, two m.2 ports, one of which being NVMe capable. 
  • ASUS GeForce GT730 2gig ddr3 gpu (the pcie witdth on this card is cut in half, so it's native x8)
  • Cheap chinese adapter I bought from Aliexpress ($7 one I believe you call it 😀 ) That does x16 to x1 NGFF via usb 3.0 cable which I've read was successfull in a few builds
  • Some random atx PSU lying around to power that thing up

Now the problem is when I put everything together, turn it on and nothing happens.

 Tried going into bios: tab there called "nvme controller info" that only does show a message "no drive detected" 

Neither Windows 10 recognise any changes to hardware. Device manager shows no new stuff found. I even tried clean install of w10, didn't help. Tried hotplugging as well as putting pc to hybrid sleep and then inserting the card - all in vain.

Nvidia Driver installs weren't succesfull either: it just says no compatible cards found upon the beginning...

The Gpu dock and the card itself get slightly warm to the touch after a while, which proves current flowing through them.

Oh yeah, I'm planning to use the internal display (13" IPS FHD)

 

Is there anything I can do to get the motherboard at least detect the eGpu?

I'm fine about purchasing that soft for $15 if that's the only way to get things running!

Will be waiting for the response

Bios version AMI 2.18.1263 dated 2017

 

Pending: Add my system information and expected eGPU configuration to my signature to give context to my posts


ReplyQuote
wenguiW
(@wenguiw)
New Member
Joined: 4 months ago
 

Pls help... i tried installing old drivers, modified drivers, the fixer and always persist the error, what should i do???

I have EXP GDC Beast 8.5c NGFF version using 12V

A9-9420 APU - HP 15-bw0xx

I saw that in safe mode if it works

HP 15-BW064NS || A9-9420 + NVIDIA GT 1030 LP + EXP GDC 8.5c (Not works, i need help :c)


ReplyQuote
walterego221
(@walterego221)
Active Member
Joined: 2 years ago
 

I have the beast with mpcie and the GTX 670. I tried to connect it to my notebook and the card is recognized but it doesn't work. error43.
My notebook has a 7700hq and a 950m. can I do something or do I give up?

This post was modified 3 months ago

Pending: Add my system information and expected eGPU configuration to my signature to give context to my posts


ReplyQuote
(@kian_moiny)
Eminent Member
Joined: 1 year ago
 

Hi guys

I have a lenovo z50-70 and I’ve connected an RX 470 to it using a 430watt PSU and ADT-Link R53SR.

I’ve removed the bios whitelist and yet it is not recognized in device manager or elsewhere, the driver does not install.

Where have I gone wrong?

Lenovo Z50-70, AMD Radeon RX 470, ADT-Link R53SR, 430W PSU


ReplyQuote
(@ethan_zheng)
New Member
Joined: 3 months ago
 

I have a GTX 670 connected to my laptop via ExpressCard (EXP GDC Dock) and it's been working fine for the past few months except I recently got a (EVGA) GTX 1050 and am planning to upgrade. However, when I installed it, I was getting no video output (to my monitor) from it. I installed/reinstalled all the drivers (using drivers from both NVIDIA and EVGA's website) and found out in Device Manager that Windows had stopped/disabled the GPU because it was reporting problems (code 43 if it helps). It detects my graphics card as a GTX 1050 and after installing drivers, it said a restart should work which is what I did, but didn't work. But then, I plug back in my GTX 670 and everything was working fine (I didn't even need to reinstall drivers or anything, Windows just recognized it and it sent a display signal to my monitor). I'm suspecting maybe it's something to do with power draw? My GTX 670 uses 2 6-pin connectors while the GTX 1050 doesn't use any external power (and I assume draws power in from the PCIe slot). Or is it just a case of old hardware not supporting newer hardware? Or is there something wrong with the GPUs in Device Manager? (I disabled my dGPU but left my iGPU and Optimus turned on)

I'm using a Dell Latitude E6520

  • Intel Core i7 2760QM

  • 16GB DDR3

  • Intel HD 3000 (iGPU)

  • NVIDIA NVS 4200M (dGPU) (disabled)

  • NVIDIA GTX 670 (eGPU)

  • NVIDIA GTX 1050 (trying to upgrade to)

Pending: Add my system information and expected eGPU configuration to my signature to give context to my posts


ReplyQuote
(@adam_kilian)
Active Member
Joined: 5 months ago
 

Hi, I have a problem witch PCIe bandwidth, when i use  gpu-z  render test or other 3d app banwitch is only  x1 1.1 ( it should be x1 2.0).  My dell have a i7-4910 cpu and  rx570  is plugd witch  exp gdc v 8.5 . HDMI audio and optimus is disable, external monitor conected

fgfg
This post was modified 3 months ago

Pending: Add my system information and expected eGPU configuration to my signature to give context to my posts


ReplyQuote
(@kian_moiny)
Eminent Member
Joined: 1 year ago
 

Hi

I have progressed to the point that I am now able to install drivers. I was able to fool windows by having the wifi in slot and changing it while the computer is in sleep it does recognize the GPU and the drivers install but it requires a reboot afterwards. If I have the GPU attached while booting I will get a BSOD even if I do manage to get through windows will refuse to detect the GPU. 
What should I do?

Lenovo Z50-70, AMD Radeon RX 470, ADT-Link R53SR, 430W PSU


ReplyQuote
Hamburglar
(@hamburglar)
Active Member
Joined: 3 months ago
 

@adam_kilian

my Expresscard GPU would present as x1 1.1 while just idle on the Windows desktop.  However, as soon I would start a 3d graphics task like watching a film with VLC, it would bump up to x1 2.  As soon as I'd close out of VLC it would revert back to 1.1 after like 5-10 seconds.  Hopefully yours behaves similarly.

Edit:  I just read Nando's first post in this thread and that's exactly what's going on.  He says the following.

The eGPU is reported as running at x1 1.1 link speed in  GPU-Z  rather than x1 2.0

Click the “?” next to Bus Interface to perform a render test. This will take the eGPU out of lower power x1 1.1 Gen1 mode and (usually) switch to x1 2.0 (Gen2) mode. If it still remains in x1 1.1 mode then you can uprate your link from Gen1 to Gen2 using BIOS options or  nando’s eGPU Setup 1.35

This post was modified 3 months ago

Pending: Add my system information and expected eGPU configuration to my signature to give context to my posts


ReplyQuote
(@gamerstone_point)
New Member
Joined: 3 months ago
 

hello im french so sorry for the bad english,

i have an old lenovo yoga 2 pro with a smashed screen so i wanted to try to add a egpu to it i bought a 1650 , a vs550 psu ,a lcd, and a EXP GDC 8.5C m.2 type A

i achived to boot only 2 times each time whent it posted i got the lenovo logo(wich meen it's not a driver issue)

the first time it crashed at windows boot screen and then no post for a long time after testing a lot of things it posted again

this time i installed the gpu driver and rebooted and then no post

now i still can't get pc running

 

my setup:

my doesn't have a dgpu only igpu

i have exp gdc connected to the psu by the 24pin + 4p and by a 6p

my gpu is conneted by 6p and into the slot

i removed the wifi card and bluged in the adapted

 

what i tryed:

removing the wifi card and booting the pc (accecing it throuth chrome desk) the put it in sleed mod hot swap boot again but no gpu detected

removing the 6p from the dock

tested every position of the switches(of the EXP GDC)

 

what i found :

i found pictured of the bios so i can navigate in it blindly

all my working attempt were with the 6p of the dock

all my working attemps were with the psu switch on the exp gdc to on

*

UPDATE:

i can now start the pc with no issue at will but i have error 43 and gpu-z report 0mb of gpu ram and my clock are 300mhz under normal

i tried changing the timeing but then my pc dosen't boot so im stuck with this error

 

This post was modified 3 months ago

Pending: Add my system information and expected eGPU configuration to my signature to give context to my posts


ReplyQuote
(@steve_tsokev)
New Member
Joined: 3 months ago
 

Unfortunately this script did not work for me. According to its description it is for eGPU running on a mPCIe, EC, M.2, LUA interface. Is mPCIe supposed to be Mobile PCI Express Module a.k.a MXM? As my P1000 card is on a MXM Type A slot. When I run the script, this is what I get: https://www.screencast.com/t/1DErxXgCtI

GPU-Z actually lists the clocks, but does not list the Memory Size and Bandwidth: https://www.screencast.com/t/rNwxvfarx

 

This post was modified 3 months ago

Pending: Add my system information and expected eGPU configuration to my signature to give context to my posts


ReplyQuote
(@amirul_aiman)
New Member
Joined: 3 months ago
 

I setup the exp gdc pci e graphic card dock and run into some few problems. Any help will be  appreciated. Using elitebook 850 G1 running windows 10.

When i connect 6 pin pci e pin from psu to gtx graphics card the laptop does not start even to bios. It only shows light colured that it is on but nothing more. All other cables are connected to the exp gdc dock except the extra power output area.

When i remove the pci e pin from psu that is connected to the gtx 960 graphic card and laptop can boot.

this is pictures my laptop became light coloured after install egpu gtx960;

https://imgur.com/Jge8RHu

https://imgur.com/80bDE7q

I also have done updated  bios version to latest. But still same.

i have try my laptop egpu gt710 exp gdc, it work prefectly but use gtx960 have problem.

i have try check the gtx960 at my member's laptop, it work properly. the gtx960 not have problem.

Pls how can i fix the problem

This post was modified 3 months ago

Pending: Add my system information and expected eGPU configuration to my signature to give context to my posts


ReplyQuote
Hugo César Paduan
(@hugo_cesar_paduan)
Active Member
Joined: 2 months ago
 

Hi,

It's needed to unlock bios to eGPU work? Because the device doesn't appears on Device Manager... Please, help!!! >>> ACER ASPIRE VX5 951G, the eGPU is Exp GDC Beast v8.5, the graphic card is 1660ti

This post was modified 2 months ago

Pending: VX5 591G eGPU Beast v8.5 HCPaduan to give context to my posts


ReplyQuote
(@paulus_rama_bimantoro)
New Member
Joined: 2 months ago
 

Hello guys,

I got this egpu system

-Dell N5110 I7 (Gt 525m dgpu)

-mpcie gdc exp 8.5c

-Psu hexa plus 550w

 

My egpu setup system works fine with gtx 750ti, I just need disable integrated nic on bios, and plug everything. Viola everything works fine my egpu running well with external monitor & newest nvidia driver.

 

But now I got 8gb RX 580 and trying to upgrade my egpu system. When I try to connect with RX 580. My laptop screen got blackscreen and nothing is happened. Can someone help me?

Pending: Add my system information and expected eGPU configuration to my signature to give context to my posts


ReplyQuote
(@guilherme_lopes)
New Member
Joined: 2 months ago
 

Hello guys, my egpu(9500 GT and tried with one GTX 760) is detected by Device Manager, but when I start any games, they don't work with the eGPU, only with my processor.

And the NVidia Control don't open, shows this message: NVIDIA Display settings are not available.

Can someone help me please? I don't know what more I can do...

My notebook: HP 1000-1440BR

HP 1000-1440BR Notebook i5-3320m 2.6-3.3ghz | 8GB RAM


ReplyQuote
(@alejandro_tejada)
New Member
Joined: 2 months ago
 

I recently bought an external adaptor for my graphic card via mPCIe. I connect all to my computer and try to star windows but it shows me a blue screen saying that "ACPI BIOS ERROR". I have been browsing a lot for the internet but don.t find anything for a fix that.

The laptop is an HP 15-d006es (but I have changed the CPU to an i7-3630QM and I have added 4GB more of Ram)

BIOS is an InsydeH2O v3.7 F.1B

The Graphic card is an AMD Sapphire R9 380X Nitro Dual-X OC 4GB GDDR5 (I connect it to an external monitor because I read that AMD only found in external monitors and not in the same monitor of the laptop)

The adaptor is an EXP GDC Beast 8.5c

Thank you in advance

 

 

Hp 15-d006esbut whit i7 3630qm and 4GB more of ram


ReplyQuote
Hugo César Paduan
(@hugo_cesar_paduan)
Active Member
Joined: 2 months ago
 

Hi, I want to know how enable eGPU on acer vx5 591g... the device doesn't appears in devices manager!

Pending: VX5 591G eGPU Beast v8.5 HCPaduan to give context to my posts


ReplyQuote
(@florin_samareanu)
Eminent Member
Joined: 4 months ago
 

@hugo_cesar_paduan Amazon’s website lists a USB-C port not thunderbolt. 

 

16'' Macbook Pro - Razer Core X Chroma - PowerColor Red Devil 5700XT - LG 27UK850


ReplyQuote
 of  16